2014 Latest Cisco 200-120 Dump Free Download(181-190)!

QUESTION 181
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow? (Choose three.)

A.    source IP address
B.    source MAC address
C.    egress interface
D.    ingress interface
E.    destination IP address
F.    IP next-hop

Answer: ADE

QUESTION 182
What are three factors a network administrator must consider before implementing Netflow in the network? (Choose three.)

A.    CPU utilization
B.    where Netflow data will be sent
C.    number of devices exporting Netflow data
D.    port availability
E.    SNMP version
F.    WAN encapsulation

Answer: ABC

QUESTION 183
Which two statements about the OSPF Router ID are true? (Choose two.)

A.    It identifies the source of a Type 1 LSA.
B.    It should be the same on all routers in an OSPF routing instance.
C.    By default, the lowest IP address on the router becomes the OSPF Router ID.
D.    The router automatically chooses the IP address of a loopback as the OSPF Router ID.
E.    It is created using the MAC Address of the loopback interface.

Answer: AD

QUESTION 184
What parameter can be different on ports within an EtherChannel?

A.    speed
B.    DTP negotiation settings
C.    trunk encapsulation
D.    duplex

Answer: B

QUESTION 185
What are two benefits of using a single OSPF area network design? (Choose two.)

A.    It is less CPU intensive for routers in the single area.
B.    It reduces the types of LSAs that are generated.
C.    It removes the need for virtual links.
D.    It increases LSA response times.
E.    It reduces the number of required OSPF neighbor adjacencies.

Answer: BC

QUESTION 186
What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)

A.    It requires the use of ARP.
B.    It can support multiple IPv6 subnets on a single link.
C.    It supports up to 2 instances of OSPFv3 over a common link.
D.    It routes over links rather than over networks.

Answer: BD

QUESTION 187
When a router undergoes the exchange protocol within OSPF, in what order does it pass through each state?

A.    exstart state > loading state > exchange state > full state
B.    exstart state > exchange state > loading state > full state
C.    exstart state > full state > loading state > exchange state
D.    loading state > exchange state > full state > exstart state

Answer: B

QUESTION 188
A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?

A.    the port-channel 1 interface
B.    the highest number member interface
C.    all member interfaces
D.    the lowest number member interface

Answer: A

QUESTION 189
What command sequence will configure a router to run OSPF and add network 10.1.1.0 /24 to area 0?

A.    router ospf area 0
network 10.1.1.0 255.255.255.0 area 0
B.    router ospf
network 10.1.1.0 0.0.0.255
C.    router ospf 1
network 10.1.1.0 0.0.0.255 area 0
D.    router ospf area 0
network 10.1.1.0 0.0.0.255 area 0
E.    router ospf
network 10.1.1.0 255.255.255.0 area 0
F.    router ospf 1
network 10.1.1.0 0.0.0.255

Answer: C

QUESTION 190
What OSPF command, when configured, will include all interfaces into area 0?

A.    network 0.0.0.0 255.255.255.255 area 0
B.    network 0.0.0.0 0.0.0.0 area 0
C.    network 255.255.255.255 0.0.0.0 area 0
D.    network all-interfaces area 0

Answer: A

If you want to pass the Cisco 200-120 Exam sucessfully, recommend to read latestCisco 200-120 Dum full version.